Skip to main content
NEW New Dedicated KIA Support Portal Are you a KIA customer?
Go to KIA Support Portal →

PDI Error Code Quick Reference Table

Oscar Eom
Updated

This provides dealers using the Hyundai·Genesis PDI (pre-delivery inspection) app with messages, stages of occurrence, key causes and immediate on-site actions for each error code.

Immediate On-site Actions by Error Code

Error Code Message Stage of Occurrence Key Cause Immediate On-site Action
Code 0319

Vehicle info download failed (0319)

 VIN lookup Delayed vehicle information response (60-second timeout)

This is not a device fault.

  1. Please try the lookup again after a short while, or carry out an offline inspection if urgent.
Code 502

VIN information does not exist on server (502)

 VIN lookup Before server synchronisation of new vehicle dispatch information (10~12 KST), or a CKD/pre-production vehicle
  1. Please check whether this is a mass-production vehicle.
  2. Please try the lookup again after server synchronisation, or use an offline token.
Code 912

Invalid Field Data (912) (stops at 74%)

 Results upload Missing Starting Miles on page 7 of the inspection sheet, or special characters in the RO
  1. Please go to page 7 of the sheet, enter the starting mileage (numbers) correctly and resend.
Code 1000

Failed to turn on Shipping Mode (1000)

 After the test drive Attempt to enter Shipping Mode with the engine running (Engine ON) immediately after driving
  1. Please switch off the engine (Engine OFF), press the [Start] button 2 times without pressing the brake (IG ON), then try again.
Code 1003

Bluetooth connection has been lost (1003)

 Auto VIN / Test drive
  • VIN not recorded in the ECU
  • Outdated app/DB
  • Outdated PIM(Mini VCI) FW
  1. Please check the engine ECU VIN Write using GDS Smart.
  2. Please update the app/DB to the latest version.
  3. Please update the PIM(Mini VCI) FW.
Code 1004

Failed to download configuration for CRL (1004)

 App installation / Authentication Waiting for security certificate synchronisation
  1. Please try logging in again after some time.
  2. Please contact the customer support centre if this continues to occur.
Code 1015

There are no Test Drive items / Failed to read 5 times (1015)

 Entering the test drive
  • Residual cache from the previously inspected vehicle
  • Vehicle not started (Engine ON / EV READY)
  • New vehicle DB not updated
  1. Please close the app completely, then relaunch it.
  2. Please check Engine ON(READY) and that the doors are closed.
  3. Please update to the latest diagnostic DB.
Code 1028

This inspection is not supported (1028)

 Battery inspection Device language set to a non-official language, or missing battery master DB for a new model
  1. Please change the tablet language to the local official language and update the model DB.
Code 1029

Unknown error (1029)

 VCI II(2) pairing Incorrect Bluetooth pairing PIN number entered (0000, 1234, etc.)
  1. Please enter the official VCI II(2) pairing PIN number 0701.
Code 1064

No campaign data (1064)

 Campaign check Campaign not registered on the PDI web administrator site (Local Campaign)
  1. The corporate administrator should register it under System Management > Local Campaign on the PDI web.
Code 1093

Error Code 1093

 Results upload Local attachments lost/corrupted due to not being sent for a long period

Recovery is not possible.

  1. Please reinstall/reset the app, reinspect the vehicle and upload immediately upon completion.
Code 1999

Firmware could not be updated (1999)

 VCI III(3) update Bluetooth wireless bandwidth limitations and packet loss (stops at approximately 2%)
  1. Please connect VCI III(3) directly to the tablet using a USB-C wired cable and perform the update.
Code 2994 (2995/2996)

Engine ON or Operating electrical features (2994) / Ampere Check Fail

 Entry Check / Auto Check
  • Engine running or air conditioning/headlamps switched on
  • Battery discharged (below 11.8V)
  • IBS sensor 0.00A
  1. Please set Engine OFF & IG ON and turn all electrical equipment OFF.
  2. Please charge the battery (SOC 70% or above).
  3. Please reset the battery (-) terminal (Cap Discharge).
Code 2998

Failed to send Auto Check config file (2998)

 Entering Auto Check PIM(Mini VCI) flash memory/hardware communication fault
  1. Please check that the PIM(Mini VCI) 3-colour LED flashes and replace it with another functioning PIM(Mini VCI) module.

Comments

0 comments

Please sign in to leave a comment.